EN CN
Home / Services / Pump Encyclopedia / Pump Knowledge / Assembly and disassembly of vertical stainless steel multistage pump

Assembly and disassembly of vertical stainless steel multistage pump

25 May 2020Email

Assembly and disassembly of vertical stainless steel multistage pump

 

        ● Put the positioning sleeve on the shaft, put the impeller, impeller spacer, guide vane, support guide vane, etc. until the last impeller, and then install the inlet impeller gland, washer, tighten the nut, pay attention to the position of the support guide vane, The spacing position should be even, and the supporting spacer and bearing should be sleeved at the same time.

        ● Install the stainless steel vertical multi-stage pump inlet guide vane on the inlet and outlet water body and the base, and then install the installed parts on the inlet guide vane.

        ● Install O-ring on the inlet and outlet water body, put on the outer cylinder, and install the outlet guide vane.

        ● Put the bracket with O-ring, seal seat and spring steel wire on the outer cylinder, and tighten the four tie rod nuts on the base. Take care not to tighten them at once, but tighten them symmetrically in turn.

        ● Install and tighten the mechanical seal, install the motor and the coupling, screw on the coupling (do not tighten), push the coupling including the pump shaft towards the base to the end, and then move it about 1mm in the opposite direction. Tighten the screws, and note that the spacing between the two coupling blocks should be even.

        ● Tighten the set screw on the mechanical seal, and rotate the coupling, the shaft should rotate flexibly without stagnation and tightness. The disassembly of the pump is performed in the reverse steps above.

  ● Install the inlet and outlet water body on the base, set flanges on both sides, and install the inlet and outlet guide vanes.

        ● Install the first impeller on the shaft, tighten the nut and sleeve the impeller in the inlet ring seat of the water inlet guide vane, install the guide vane, impeller, and support guide vane until the water outlet guide vane. leaf.

        ● Shaft components: install the upper and lower shaft sleeves, gland, washer, tighten the screws, install the lower wear-resistant bearings on the inlet and outlet water bodies, install the washers, tighten the screws, then re-sleeve the shaft components on the inlet and outlet water bodies, and install O-rings, Apply lubricating oil and put on the outer cylinder.

        ● The pull rod is installed on the base, the O-ring, adjustment pile, screw plug, and the plug are discarded on the sealing seat, and then the sealing seat is sleeved on the pull rod, the washer is installed, and the nut is tightened.

        ● Install the mechanical seal on the seal seat, install the sealing gland, tighten the screw, and then tighten the screw on the mechanical seal, then lift the shaft upwards, and install the adjusting plate.

        ● Install the bracket and motor on the pump head

        ● Finally install the coupling, tighten the screw, and then take out the adjusting piece. Rotate the coupling, the pump shaft should rotate flexibly without stagnation and tightness. The disassembly of the pump is carried out in reverse steps.

Related Pump Knowledge
More Pump Knowledge
25 Mar 2024
Large displacement pump type           Large displacement pump, as the name suggests, is a pump with a very large flow, and ...
Read more
18 Mar 2024
         Coal mine drainage pump is one of the indispensable mechanical equipment in coal mine, its role is reflected in many...
Read more
07 Mar 2024
        The working principle of the multistage centrifugal pump is: relying on the high-speed rotating impeller, the liquid obtai...
Read more
29 Feb 2024
          Centrifugal pump is a common and important type of pump, which is widely used. However, in the process of using centrifugal pumps, irrigatio...
Read more
Related Products
More
Split Case Pump
Split Case Pump
  • Capacity:60-33005m³/h
  • Head:0.95-30.2bar
  • Price:$2200-215000
Double Suction Pump
Double Suction Pump
  • Capacity:60-33005m³/h
  • Head:0.95-30.2bar
  • Price:$2200-215000
Single Stage Chemical Pump
Single Stage Chemical Pump
  • Capacity:5.5-2600m³/h
  • Head:1.6-25bar
  • Price:$4300-37000
End Suction Chemical Pump
End Suction Chemical Pump
  • Capacity:5.5~400m³/h
  • Head:0.42-12.5bar
  • Price:$560-9800
Need More Information?
Contact us for more details about our pump, solutions and services.
Contact ZB
Tel
0086 731 88192011
Leave a message
Name*
Tel
Email*
Area
Products
Split Case Pump
Metallurgy
Mining Industry
Urban Water Supply
Petrochemical
Light Industry
Electricity
Chemical Industry
Farmland Irrigation
Other
Provide your comments and questions.